Specifications
| Metric | Value | Unit | Basis, formula & conditions |
|---|---|---|---|
| Length | 1200 | mm | Documented specificationProduct sheet · p. 2Reviewed |
| Width | 740 | mm | Documented specificationProduct sheet · p. 2Reviewed |
| Height | 1215 | mm | Documented specificationProduct sheet · p. 2Reviewed |
| Cabinet footprint | 0.888 | m² | Calculated example 1.200 × 0.740 = 0.888 Length × width only; operating and service clearance is additional. Product sheet · p. 2Reviewed |
| Total electrical load | 0.5 | kW | Documented specification Electrical power rating, not measured energy consumption. Product sheet · p. 2Reviewed |
| Motors | 0.2 | kW/motor | Documented specification Electrical power rating, not measured energy consumption. Product sheet · p. 2Reviewed |
| Motor count | 2 | motors | Documented specificationProduct sheet · p. 2Reviewed |
| Voltage | 380 | V | Documented specification Quick cycle: approximately 15 seconds for two molds, excluding handling. Confirm 50/60 Hz configuration before ordering. The supplied manual references compressed air; our team will confirm the requirement for the delivered machine. Product sheet · p. 2Reviewed |
| Frequency options | 50 / 60 | Hz | Configuration option 50 or 60 Hz configuration must be confirmed before ordering; not a continuous adjustment range. Product sheet · p. 2Reviewed |
| Power phases | 3 | phases | Documented specification Quick cycle: approximately 15 seconds for two molds, excluding handling. Confirm 50/60 Hz configuration before ordering. The supplied manual references compressed air; our team will confirm the requirement for the delivered machine. Product sheet · p. 2Reviewed |
| Water inlet size | 3/4 | nominal inches | Documented specification Nominal connection size; do not interpret it as a measured bore diameter. Product sheet · p. 2Reviewed |
| Drain diameter | 38 | mm | Documented specificationProduct sheet · p. 2Reviewed |
1. Separate cabinet footprint from working space
The cabinet projection is 1.200 × 0.740 = 0.888 m². It is not the total installation area. Operators need space to load and unload; maintenance access, hose routing and separation of dirty and cleaned molds also use floor area.
Measure doorways, corners and the unloading route. Machine dimensions are not packed dimensions. Ask for shipping dimensions and weight, lifting arrangements and agreed delivery scope before booking transport.
2. Low power does not mean an ordinary socket
The data sheet lists 0.5 kW total electrical load and two 0.2 kW motors. Its standard supply is 380 V three-phase. Send the actual site voltage, frequency and phase information to V-TAI rather than assuming the local supply matches.
Confirm the delivered 50/60 Hz configuration in writing. A qualified installer should verify the required electrical connection and protection against the final machine documents. Do not use this article to choose wiring or protective-device ratings.
3. Trace water and drainage before locating the machine
The published inlet is 3/4 inch and the drain diameter is Ø38 mm. Connection size is not a water-consumption figure. No validated liters-per-mold or supply-pressure value is provided here. Confirm site requirements with V-TAI.
Plan accessible connections and a clear discharge route without obstructing the operator. The manual references compressed air; whether it is required and the pressure, flow and connector specifications must be confirmed for the delivered unit.
4. Agree on commissioning and the process after washing
Prepare representative dirty molds and an acceptance checklist before delivery. Confirm who handles unloading, connection, operator instruction and trial washing. Keep approved settings and inspection records available to the team.
The machine uses cold water and has no heated sanitizing cycle. Reserve a defined route for the facility’s further sanitation, drying and storage. An installation plan should include these handoffs, even though they are not part of the cabinet footprint.
A FEW USEFUL ANSWERS
Does the machine need only 0.888 m²?
No. That is the cabinet footprint; add space for handling, maintenance and connections.
Can it use any local 380/400/415 V supply?
Do not assume compatibility. Send the actual supply details and confirm the delivered configuration with V-TAI.
The short answer
Approve the site layout, actual electrical supply, water and drain route, and delivery responsibilities before ordering.
Talk to an expertSources & product documentation
Based on V-TAI product information and the supplied product sheet. Final configuration and sample suitability should be confirmed with V-TAI.
V-TAI · VT-CE-CM2 ↗Download product sheet · PDF · Chinese · 2 pages ↗